How do I troubleshoot EIGRP configuration?
Check for bad physical infrastructure. Ensure that router ports are plugged into the correct hubs. Check for filters blocking EIGRP packets. Verify router configurations — check IP addresses, masks, EIGRP AS numbers, and the network numbers defined under EIGRP.
Does EIGRP work with IPv6?
The EIGRP for IP version 6 will work on the same way as EIGRP IP version 4, where it can configure and managed separately. The EIGRP is inherently the multicast routing protocol because it will support for the non IP protocols. The mechanisms and configuration techniques will slightly vary from the IPv4 to IPv6.
When configuring EIGRP on IPv4 and IPv6 What is the major difference?
EIGRP for IPv6 still possesses the same overall features and operation as EIGRP for IPv4; only there are a few major differences between them: EIGRP for IPv6 uses IPv6 prefixes and lengths rather than IPv4 subnets and masks. To establish EIGRP for IPv6 neighbor relationship, it uses IPv6 link-local addresses.
How do I check my EIGRP status?
debug ip eigrp Examples. You can use the debug ip eigrp command to verify EIGRP operation. This command displays EIGRP packets that this router sends and receives. Example 3-34 shows the contents of the updates that are reported when you use the debug ip eigrp command on R2 to monitor when an interface on R1 comes up.
Is EIGRP difficult to configure?
EIGRP is not too difficult to configure and it can handle even the largest networks.
Which commands can you use to troubleshoot EIGRP on your network?
The following three commands are used to verify and troubleshoot EIGRP:
- show ip route.
- show ip protocols.
- show ip eigrp neighbors.
- show ip eigrp topology.
- debug eigrp packets and debug ip eigrp notifications.
What commands are used to enable EIGRP for IPv6 on an interface?
EIGRP for IPv6 Configuration
| 1 | Enter global configuration mode |
|---|---|
| 3 | Enter interface configuration mode |
| 4 | Enable EIGRP for IPv6 on the interface |
| Repeat steps 1-4 on all EIGRP for IPv6 interfaces | |
| 5 | Enter EIGRP for IPv6 router configuration modeNote: This is a global configuration mode command |
Which multicast address does EIGRP for IPv6 use?
Solution(By Examveda Team) EIGRPv6’s multicast address stayed very near the same. In IPv4 it was 224.0. 0.10 ; now it is FF02::A (A=10 in hexadecimal notation).
What can be verified with the output of show IPv6 protocols?
The output from the show ipv6 protocols command is useful in debugging routing operations. The Interfaces section shows which interfaces EIGRP for IPv6 have been enabled. This is useful in verifying that EIGRP is enabled on all of the appropriate interfaces with the correct autonomous system number.
How does EIGRP for IPv6 select a router ID?
How does EIGRP for IPv6 select a router ID if the router ID is not manually configured? It uses the highest link-local address that is configured on an active EIGRP for IPv6 interface. It is uses the EUI-64 process to automatically generate the router ID based on the highest configured IPv6 address value.
How do I fix EIGRP stuck in active?
The tool that you need to troubleshoot the EIGRP stuck in active error is the show ip eigrp topology active command. This command shows what routes are currently active, how long the routes have been active, and which neighbors have and have not replied to the query.
What is stuck in active in EIGRP?
EIGRP is a reliable protocol and for each query a router sends to its neighbors it must get a reply in response within 3 minutes. If the router does not receive a reply to ALL its outstanding queries it will put the route in SIA (Stuck in Active) state and will kill the neighbor adjacency.
Why does EIGRP for IPv6 take so long to verify?
This is because EIGRP for IPv6 uses the link-local addresses to communicate and establish adjacencies. In other words, we are just checking the content of the neighbor table. If all adjacencies are up, but you have problems with some routes, the next step is the topology table verification.
Why are there no IPv6 neighbor adjacencies on my EIGRP?
No IPv6 routes have been learned from other routers and there are no neighbor adjacencies. Issue the no shutdown command under the EIGRP for IPv6 routing process. The S0/0/1 interface is configured in the wrong EIGRPv6 process.
How to create EIGRP for IPv6 routing instance?
Create an EIGRP for IPv6 routing instance with ipv6 router eigrp , the AS ID must match on all routers Here, you need to define a router ID with eigrp router-id , and turn on the process with no shutdown You can propagate connected networks without having them join the EIGRP for IPv6 instance.
How do I troubleshoot EIGRP link errors?
Ping the EIGRP neighbor unicast IP address (with the size of the ping set to the full MTU size of the link, and with the Do Not Fragment bit (DF-bit) set) in order to verify. A one-way link can cause this problem as well.